Feiyiya Inclined Plate Clarifiers Use Gravity & Innovative Engineering
A gravity clarifier is the most economical method of removing solids from liquids, using natural gravity as the source of energy and it is free. A clarifier simply provides a non-turbulent zone where heavier than liquid solids, suspended by turbulence, are given sufficient time to settle to a quiescent surface. The HEI inclined plate clarifiers are compact units with multiple layers of settling area utilizing less than 25% of the floor space required by conventional clarifiers.
Principle of Clarifiers
A particle carried forward by the velocity of the liquid flow must settle at a rate that allows it to reach the bottom before passing through the clarifer. Thus, particles beginning at a point [a" must traverse some route lying between ab and ab` in order to avoid being carried over the outlet.
If V is the horizontal velocity of the liquid, S the solids particle vertical settling velocity, L the length of the settling device, and D its depth, then particles entering at point A will settle to the bottom of the device only if V does not exceed: S(L/D)Since Vmax / S = L / D then, Vmax = S (L / D)
Inclined plate clarifier, Lanmei inclined plate clarifier, Inclined Tube Settler,High-Efficiency Inclined Tube Wuxi Feiyiya Environmental Protection Technology Co., Ltd. , https://www.feiyya.com
Therefore, the velocity at which a horizontal clarifying device may be operated successfully is directly proportional to its length and inversely proportional to its depth.
This analysis applies to multiple horizontal plate units also. The spacing between plates is usually a few inches as opposed to a depth of several feet in a horizontal tank; therefore, [settling-out" times are dramatically reduced. The flow must be non-turbulent to prevent settled solids from being re-entrained within the moving liquid. Small plate spacing and a large surface area permits laminar flow at higher velocities than large horizontal tanks would allow.
Horizontal clarifying devices become self-flushing if they are inclined at an angle which exceeds the angle of repose of the settled solids. In such cases, flow enters the lower end of the device where settling particles move to the floor eventually sliding back out the entrance. Clear effluent leaves the top of the device.
However, when the device is inclined, the furthest settling particles no longer fall through distance D but some longer distance D`. This new longer settling distance D` is related to D by the relation: D = D` cos Ø.
Theta [Ø" is the angle, the device is inclined to the horizontal plane. Thus settling distance is increased by the factor: 1/cos Ø In the case where Ø = 60º, 1/cos Ø = 2.
The maximum settling distance is twice the distance between the plates. It is apparent then that the lower the angle of inclination, the smaller the settling distance. However, the angle of inclination must exceed the angle of repose of the solids to be separated. The previous equation may be modified to express the cosine of an inclined plate clarifying system as:
Vmax = L / (D / cosØ) (s) = L·cosØ / D (s)
Inclined Plate Clarifiers
A reduction of the required floor space is acquired by diminishing the separation between the horizontal plates to a few inches and stacking the settling surfaces. Inclining the plates to provide self flushing, 45º for heavy particles and 60º for light particles, reduces the available horizontal projected area (effective settling area) by a factor equivalent to the cosine of the angle. The surface area diagram (below) graphically compares the floor space requirements of an HEI inclined plate clarifier with the equivalent horizontal projected settling area.
Settling Rate
The settling rate for a specific solids should be determined by standard laboratory tests. Light particles, such as metal hydroxides, usually require a design parameter of 0.25 – 0.50 gallons per minute per square foot of horizontal projected area. These low density solids require the inclined plates to be set at a 60º angle to induce the particles to slide down the plate. Heavier particles (such as sand that easily flow) will readily slide from plates set at a 45º angle.
Maximum flow rate of an inclined plate clarifier is based on the flow rate per unit of a horizontally projected surface area. Retention time in the clarifier is not a design criteria. However, attaining optimum performance requires the prudent design to recognize several additional, very important factors.
Cleaning your glasses is an essential part of maintaining clear vision and extending the life of your eyewear. Just like any other daily item, your glasses accumulate dirt, oils, and smudges from regular use. These build-ups can make it harder to see clearly and may even damage the delicate coatings on your lenses over time. Proper cleaning not only keeps your vision sharp but also helps preserve the quality of your frames and lenses.
One of the easiest and most effective ways to clean your glasses is with a simple routine using warm water, mild dish soap, and a lint-free cloth. Before you start, make sure to wash your hands thoroughly to avoid transferring oils or dirt onto your glasses. Then, rinse your glasses under lukewarm water to remove any loose debris. Apply a small drop of dish soap to each lens and gently rub them in circular motions, focusing on areas that come into contact with your face, like the nose pads and temples. After rinsing, dry your glasses with a soft microfiber cloth to avoid leaving behind any lint or smudges.
It's important to avoid harsh cleaning methods, such as using paper towels, tissues, or clothing to wipe your lenses. These materials can scratch the surface or leave behind residue. Also, never use alcohol-based products, hand sanitizers, or strong chemicals, as they can damage the special coatings on your lenses. Instead, stick to gentle, lens-safe solutions.
For a deeper clean, especially for sunglasses or blue light glasses, follow the same steps but ensure you're using products that are safe for the specific type of lenses you have. If you're traveling, consider carrying a portable cleaning kit with a microfiber cloth and a spray cleaner. This will help keep your glasses clean even when you're on the go.
Proper storage is also key to keeping your glasses in good condition. Always store them in their case when not in use, and avoid placing them in hot or direct sunlight. Handling your glasses carefully by the frame rather than the lenses can prevent unnecessary stress and potential damage.
By following these simple tips, you can keep your glasses looking great and performing at their best. Regular cleaning and proper care will ensure your vision stays clear and your eyewear lasts longer. If you ever need more guidance or have questions about your glasses, don’t hesitate to reach out to a professional for assistance.