Gabion,Gabion Wall,Gabion Cages,Gabion Wall Baskets Anping Xinghong Metal Wire Mesh Co.,Ltd , https://www.apironwire.com
The adaptability of the rice mill is very strong: the unique combined roller and combined rotary screen of the rice mill are assembled from multiple parts and can be easily restructured to meet different raw material varieties, quality, precision grade of finished products, regional climate and Positions in the process (open rough, coarse grinding, brushing) and other different needs. In addition to rice milling, only a slight adjustment to the white room configuration can also be used for sorghum, millet, wheat, barley, oats and other grain peeling and grain surface cleaning, decontamination treatment. Different combinations can be used to grind products of different quality grades and different peeling rates. Increase and decrease the number of whitening channels and change the time and intensity of grinding of sand, iron roller, rice sieve, rice knives and other adjustable rice mills in the whitening room to regulate production capacity and precision.
The small rice mill has the characteristics of high speed, low pressure, light weight, and energy saving: due to high pressure instead of high pressure, short, small, fine, and light are used to replace long, large, coarse, and heavy, and gas-solid fluidization replaces high-density extrusion. Therefore, the torque resistance of the holding roller brake is small, the energy consumption for boost heating is small, and unlike traditional two-pole motors, narrow V-shaped belts with high line speed and high efficiency transmission, the installed capacity of the 22kW rice machine can reach the installed power of 37kW. The production capacity of traditional rice mills is light, light and easy to consume.
The small rice mill can dynamically humidify and moisten the skin briefly: from the hopper to the upper and lower milling chambers, the front, middle, and rear mill shafts can be sprayed with traces of water at various places throughout the shaft, and they can be dynamically embeded in the strong tumbling mix. Alternating cycles, so that the rice grain skin moist and soft, and the endosperm binding force reduced, easy to mill off the rice kernels without hurting the endosperm. The rice grains are always in the state of high friction on the surface during the whole process of grinding, and are alternately grinded, rubbed off, washed by air, brushed and thrown by long-distance cycles, so that the finished rice is clean and complete, the endosperm does not increase water, and it is not easy to be mildewed and rancid. It highlights the wind washing, air cooling, wind transport and light negative effects of “Strong Windâ€. Traditional rice blasters are limited by the structure of the whitening chamber. When the blast air is too strong, the air inlet and outlet are difficult to close, and when the spray is too weak Difficult to enter the wind, the effect of the blast process is limited. The flow density of rice in different parts of the white room is not equal, the location of the spray is uneven, and the air blows from the high pressure area to the low pressure area. The interference disturbs the stability of the directional spiral movement of the rice grain flow, causing load instability, and even export sneeze and imports. The top material, and then lost pressure, shocks, broken pieces, paste sieve until the stuffy car. After the blast air is changed, the air pressure in the white room is pulled from the positive pressure to the negative pressure, and the white outside wind is easy to enter and is led out from the sieve belt. There is no such drawback of the spray. The super-linear velocity of the combined roller forms a large centrifugal radial force, forcing the flow of the rice grain to squeezing and rubbing off the plugging and draining; the spring steel wire woven mesh screen causes the repetitive alternating change of the internal pressure and the elastic micro-vibration along with the eccentricity. Plugging holes; Small-diameter round steel Wire Mesh screen is not easy to be broken by broken rice than punched screen sieve mesh, and the whole meter is not easy to break in the jack, and the plugging material is shaken off with screen mesh vibration or is blocked by brushing outside the screen tube. Out, so as to maintain the open mesh. The hopper and the hopper seat enter into the wind to form a wind feeding material. The tube axis with an inner diameter of 90 mm, and the four long groove inlet holes on the three-push screw and the axial end roller are used to ensure that there is sufficient cross section of the over-wind to “negativeâ€. Press" the white room into the air and the amount of wind and wind speed through the screen. The white room hood and the hoppers form a fully enclosed space and surround the rotary screen cylinder. The high pressure suction fan draws the wind from this space to a certain degree of vacuum, resulting in a sufficient pressure difference between the inside and the outside of the screen cylinder. The radial centrifugal force acts to force the wind belt in the screen cylinder to be sucked away from the screen through the screen, thus keeping the inside of the roller room in a state of negative pressure, flow state, light weight and stability, and the strong pulling wind cooperates with strong rolling. The air-solid fluidization of the white room has strengthened the wind transport and air scrubbing and throwing, so as to achieve the finished product clean and free from scouring.
The components of the small rice mill are highly versatile: rice mills are used for different purposes such as uncoating and milling rice, coarse grinding, fine grinding, brushing and wheat peeling, etc. Only need to change the combined roller and combination The individual parts of the rotary screen, the generalization degree of each derivative type of machine parts is as high as more than 90%, which is not only convenient for manufacturing but also easy to manage and use, and the manufacturing and use operating costs are low. The multi-function system of small rice mills is individually driven by the motors installed inside the engine body. They do not interfere with each other, and the transmission efficiency is high. The overall structure of the machining center and the multi-functional combination of the machine, electricity, wind and water make it possible Its safe and convenient operation, the installation of a small footprint, easy to complete combination.
The combination of small pieces of easy-to-consume small rice mills and low operating costs: The easy-to-fail working surfaces of the combination roller and the combined rotary screen are all assembled from small pieces. Each piece is short, small, light, simple and inexpensive. The different degrees of wear are local small parts replacement, respectively, cost-saving, easy manufacturing, low manufacturing and operating costs; easy to install, easy to remove, can be easily replaced on time, so that it is easy to maintain the best and the best working condition of the rice machine. Excellent process effect.
The upper and lower white machine cantilever arms of the small rice mill are all outside the rack, and the spindles and bearings do not need to be disassembled, installed, or replaced. The operation and assembly and disassembly are both convenient and easy.
For the purchase of small rice mills, most people still only care about their prices. Actually, the prices of some small rice mills are relatively low, but their functions are relatively small, and they cannot meet the needs of some scientific research units and enterprises. The price is not low, for example, some rice mills are not adaptable, there is no high-speed, low-pressure, light-negative function, the degree of generalization of parts is not high, the operating cost is relatively large, these are insufficient to make us normal demand, below Introduce a small rice mill for you, although the price is in the middle, but the function can meet the demand equipment.